Chemical Safety Data Sheet MSDS / SDS

(6L)lithium fluoride

Revision Date:2026-05-31Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

Product name: (6L)lithium fluoride
CBnumber: CB4909552
CAS: 14885-65-5
EINECS Number: 238-958-9
Synonyms: Lithium-6Li fluoride 95 atom % 6Li, 99% (CP),Lithium-?Li fluoride

Relevant identified uses of the substance or mixture and uses advised against

Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
Uses advised against: none

Company Identification

Company: Chemicalbook
Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
Telephone: 010-86108875

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

Symbol(GHS)

Signal wordDanger

Precautionary statements

P201 Obtain special instructions before use.

P260 Do not breathe dust/fume/gas/mist/vapours/spray.

P263 Avoid contact during pregnancy/while nursing.

Hazard statements

H301 Toxic if swalloed

H361 Suspected of damaging fertility or the unborn child

H362 May cause harm to breast-fed children

SECTION 3: Composition/information on ingredients

Substance

Product name: (6L)lithium fluoride
Synonyms: Lithium-6Li fluoride 95 atom % 6Li, 99% (CP),Lithium-?Li fluoride
CAS: 14885-65-5
EC number: 238-958-9
MF: FLi
MW: 25.94

SECTION 4: First aid measures

4.1 Description of first-aid measures

General advice

Hydrofluoric (HF) acid burns require immediate and specialized first aid and medical treatment. Symptoms may be delayed up to 24 hours depending on the concentration of
HF. After decontamination with water, further damage can occur due to penetration/absorption of the fluoride ion. Treatment should be directed toward binding the fluoride ion as well as the effects of exposure. Skin exposures can be treated with a 2.5% calcium gluconate gel repeated until burning ceases. More serious skin exposures may require subcutaneous calcium gluconate except for digital areas unless the physician is experienced in this technique, due to the potential for tissue injury from increased pressure. Absorption can readily occur through the subungual areas and should be considered when undergoing decontamination. Prevention of absorption of the fluoride ion in cases of ingestion can be obtained by giving milk, chewable calcium carbonate tablets or
Milk of Magnesia to conscious victims. Conditions such as hypocalcemia, hypomagnesemia and cardiac arrhythmias should be monitored for, since they can occur after exposure.Show this material safety data sheet to the doctor in attendance.

If inhaled

After inhalation: fresh air. Call in physician.

In case of skin contact

First treatment with calcium gluconate paste.In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician.

In case of eye contact

After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.

If swallowed

If swallowed: give water to drink (two glasses at most). Seek medical advice immediately.
In exceptional cases only, if medical care is not available within one hour, induce vomiting (only in persons who are wide awake and fully conscious), administer activated charcoal (20 - 40 g in a 10% slurry) and consult a doctor as quickly as possible.

4.2 Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11

4.3 Indication of any immediate medical attention and special treatment needed

No data available

4.4 Notes to physician

No data available

SECTION 5: Firefighting measures

5.1 Extinguishing media

Suitable extinguishing media

Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.

Unsuitable extinguishing media

For this substance/mixture no limitations of extinguishing agents are given.

5.2 Special hazards arising from the substance or mixture

Hydrogen fluoride
Lithium oxides
Not combustible.
Ambient fire may liberate hazardous vapours.

5.3 Advice for firefighters

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.

SECTION 6: Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact.
Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.

6.2 Environmental precautions

Do not let product enter drains.

6.3 Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully. Dispose of properly. Clean up affected area.
Avoid generation of dusts.

6.4 Reference to other sections

For disposal see section 13.

SECTION 7: Handling and storage

7.1 Precautions for safe handling

Advice on safe handling

Work under hood. Do not inhale substance/mixture.

Hygiene measures

Change contaminated clothing. Preventive skin protection recommended. Wash hands after working with substance.
For precautions see section 2.2.

7.2 Conditions for safe storage, including any incompatibilities

Storage conditions

Tightly closed. Dry. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons.

Storage class

Storage class (TRGS 510): 6.1D: Non-combustible, acute toxic Cat.3 / toxic hazardous materials or hazardous materials causing chronic effects

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Ingredients with workplace control parameters

['Component', 'CAS-No.', 'Value', 'Control\nparameters', 'Basis']	['Lithium-6 fluoride', '14885-65-\n5', 'PC-TWA', '2 mg/m3', 'Occupational exposure limits for\nhazardous agents in the\nworkplace - Chemical\nhazardous agents.']

Biological occupational exposure limits

['Component', 'CAS-No.', 'Parameters', 'Value', 'Biological\nspecimen', 'Basis']	['', '14885-65-\n5', 'fluoride', '42Millim\noles per\nmole\ncreatinin\ne', 'Urine', 'China. Biological\nOccupational\nExposure Indices']	['', 'Remarks', 'After shift', None, None, None]	['', '', 'fluoride', '7mg/g\ncreatinin\ne', 'Urine', 'China. Biological\nOccupational\nExposure Indices']	['', '', 'After shift', None, None, None]	['', '', 'fluoride', '24Millim\noles per\nmole\ncreatinin\ne', 'Urine', 'China. Biological\nOccupational\nExposure Indices']	['', '', 'Prior to shift', None, None, None]	['', '', 'fluoride', '4mg/g\ncreatinin\ne', 'Urine', 'China. Biological\nOccupational\nExposure Indices']	['', '', 'Prior to shift', None, None, None]

8.2 Exposure controls

Appropriate engineering controls

Change contaminated clothing. Preventive skin protection recommended. Wash hands after working with substance.

Personal protective equipment

Eye/face protection

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

Skin protection

This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell,
Internet: www.kcl.de).
Full contact
Material: Nitrile rubber
Minimum layer thickness: 0.11 mm
Break through time: 480 min
Material tested:KCL 741 L
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0.11 mm
Break through time: 480 min
Material tested:KCL 741 L

Body Protection

protective clothing

Respiratory protection

required when dusts are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.

Control of environmental exposure

Do not let product enter drains.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

a) Physical statesolid
b) ColorNo data available
c) OdorNo data available
d) Melting point/freezing pointMelting point/range: 842 °C
e) Initial boiling point and boiling rangeNo data available
f) Flammability (solid, gas)The product is not flammable.
g) Upper/lower flammability or explosive limitsNo data available
h) Flash pointNot applicable
i) Autoignition temperatureNo data available
j) Decomposition temperatureNo data available
k) pHNo data available
l) ViscosityViscosity, kinematic: No data available
Viscosity, dynamic: No data available
m) Water solubilityNo data available
n) Partition coefficient n-octanol/waterNo data available
o) Vapor pressureNo data available
p) DensityNo data available
Relative densityNo data available
q) Relative vapor densityNo data available
r) Particle characteristicsNo data available
s) Explosive propertiesNo data available
t) Oxidizing propertiesnone

9.2 Other safety information

No data available

SECTION 10: Stability and reactivity

10.1 Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

10.2 Possibility of hazardous reactions

No data available

10.3 Conditions to avoid

no information available

10.4 Incompatible materials

Strong oxidizing agents, Strong acids

10.5 Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

11.1 Information on toxicological effects

Acute toxicity

Oral: No data available
Inhalation: No data available
Dermal: No data available

Skin corrosion/irritation

Remarks: No data available

Serious eye damage/eye irritation

Remarks: No data available

Respiratory or skin sensitization