Chemical Safety Data Sheet MSDS / SDS
2,2-Dimethylbutane
Revision Date:2026-03-21Revision Number:1
Product identifier
- Product name: 2,2-Dimethylbutane
- CBnumber: CB7280708
- CAS: 75-83-2
- EINECS Number: 200-906-8
- Synonyms: butane,2,2-dimethyl- ;Trimethylpropane
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 010-86108875
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordDanger
P210 Keep away from heat/sparks/open flames/hot surfaces. — No smoking.
P233 Keep container tightly closed.
P273 Avoid release to the environment.
P301+P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P303+P361+P353 IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.
P331 Do NOT induce vomiting.
Hazard statements
H225 Highly Flammable liquid and vapour
H304 May be fatal if swallowed and enters airways
H315 Causes skin irritation
H336 May cause drowsiness or dizziness
H411 Toxic to aquatic life with long lasting effects
Substance
- Product name: 2,2-Dimethylbutane
- Synonyms: butane,2,2-dimethyl- ;Trimethylpropane
- CAS: 75-83-2
- EC number: 200-906-8
- MF: C6H14
- MW: 86.18
4.1 Description of first-aid measures
General adviceShow this material safety data sheet to the doctor in attendance.
If inhaled
After inhalation: fresh air. Call in physician.
In case of skin contact
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
In case of eye contact
After eye contact: rinse out with plenty of water. Remove contact lenses.
If swallowed
After swallowing: caution if victim vomits. Risk of aspiration! Keep airways free. Pulmonary failure possible after aspiration of vomit. Call a physician immediately.
4.2 Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11
4.3 Indication of any immediate medical attention and special treatment needed
No data available
4.4 Notes to physician
No data available
5.1 Extinguishing media
Suitable extinguishing mediaFoam Carbon dioxide (CO2) Dry powder
Unsuitable extinguishing media
For this substance/mixture no limitations of extinguishing agents are given.
5.2 Special hazards arising from the substance or mixture
Carbon oxides
Combustible.
Pay attention to flashback.
Vapors are heavier than air and may spread along floors.
Development of hazardous combustion gases or vapours possible in the event of fire.
Forms explosive mixtures with air at ambient temperatures.
Combustible.
Pay attention to flashback.
Vapors are heavier than air and may spread along floors.
Development of hazardous combustion gases or vapours possible in the event of fire.
Forms explosive mixtures with air at ambient temperatures.
5.3 Advice for firefighters
Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.
Remove container from danger zone and cool with water. Prevent fire extinguishing water from contaminating surface water or the ground water system.
Remove container from danger zone and cool with water. Prevent fire extinguishing water from contaminating surface water or the ground water system.
NFPA 704
2
3
0
| HEALTH | 2 | Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine) | |
| FIRE | 3 | Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions . Liquids having a flash point below 22.8 °C (73 °F) and having a boiling point at or above 37.8 °C (100 °F) or having a flash point between 22.8 and 37.8 °C (73 and 100 °F). (e.g. gasoline, acetone) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
6.1 Personal precautions, protective equipment and emergency procedures
Advice for non-emergency personnel: Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition.
Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.
Evacuate the danger area, observe emergency procedures, consult an expert.
For personal protection see section 8.
6.2 Environmental precautions
Do not let product enter drains. Risk of explosion.
6.3 Methods and materials for containment and cleaning up
Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully with liquid-absorbent material (e.g.
Chemizorb®). Dispose of properly. Clean up affected area.
Chemizorb®). Dispose of properly. Clean up affected area.
6.4 Reference to other sections
For disposal see section 13.
7.1 Precautions for safe handling
Advice on safe handlingWork under hood. Do not inhale substance/mixture. Avoid generation of vapours/aerosols.
Advice on protection against fire and explosion
Keep away from open flames, hot surfaces and sources of ignition.Take precautionary measures against static discharge.
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
For precautions see section 2.2.
For precautions see section 2.2.
7.2 Conditions for safe storage, including any incompatibilities
Storage conditionsKeep container tightly closed in a dry and well-ventilated place. Keep away from heat and sources of ignition.
Handle and open container with care. Moisture sensitive.
Storage class
Handle and open container with care. Moisture sensitive.
Storage class (TRGS 510): 3: Flammable liquids
8.1 Control parameters
Ingredients with workplace control parameters| ['Component', 'CAS-No.', 'Value', 'Control\nparameters', 'Basis'] | ['2,2-\ndimethylbutane', '75-83-2', 'TWA', '500 ppm', 'USA. ACGIH Threshold Limit\nValues (TLV)'] | ['', '', 'STEL', '1,000 ppm', 'USA. ACGIH Threshold Limit\nValues (TLV)'] | ['', '', 'TWA', '100 ppm350\nmg/m3', 'USA. NIOSH Recommended\nExposure Limits'] | ['', '', 'C', '510\nppm1,800\nmg/m3', 'USA. NIOSH Recommended\nExposure Limits'] | ['', '', 'PEL', '500\nppm1,800\nmg/m3', 'California permissible exposure\nlimits for chemical\ncontaminants (Title 8, Article\n107)'] | ['', '', 'STEL', '1,000\nppm3,600\nmg/m3', 'California permissible exposure\nlimits for chemical\ncontaminants (Title 8, Article\n107)'] |
|---|
8.2 Exposure controls
Appropriate engineering controlsImmediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.
Personal protective equipment
Eye/face protection
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses
Skin protection
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell,
Internet: www.kcl.de).
Full contact
Material: Viton®
Minimum layer thickness: 0.7 mm
Break through time: 480 min
Material tested:KCL 890 Vitoject®
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell,
Internet: www.kcl.de).
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0.2 mm
Break through time: 30 min
Material tested: P (KCL 743 / Aldrich Z677388, Size M)
Body Protection
Internet: www.kcl.de).
Full contact
Material: Viton®
Minimum layer thickness: 0.7 mm
Break through time: 480 min
Material tested:KCL 890 Vitoject®
This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN 16523-1 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell,
Internet: www.kcl.de).
Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0.2 mm
Break through time: 30 min
Material tested: P (KCL 743 / Aldrich Z677388, Size M)
Flame retardant antistatic protective clothing.
Respiratory protection
required when vapours/aerosols are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Control of environmental exposure
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Do not let product enter drains. Risk of explosion.
Information on basic physicochemical properties
- a) Physical stateclear, liquid
- b) Colorcolorless
- c) OdorNo data available
- d) Melting point/freezing pointMelting point/range: -100 °C - lit.
- e) Initial boiling point and boiling range50 °C - lit.
- f) Flammability (solid, gas)No data available
- g) Upper/lower flammability or explosive limitsUpper explosion limit: 7.7 %(V)
Lower explosion limit: 1.2 %(V) - h) Flash point-29 °C - closed cup
- i) Autoignition temperatureNo data available
- j) Decomposition temperatureNo data available
- k) pHNo data available
- l) ViscosityViscosity, kinematic: No data available
Viscosity, dynamic: No data available - m) Water solubilityinsoluble
- n) Partition coefficient n-octanol/waterNo data available
- o) Vapor pressure1,236 hPa at 55 °C 368.8 hPa at 20 °C
- p) Density0.649 g/cm3 at 25 °C - lit.
- Relative density0.649 g/mL at 25 °C(lit.)
- q) Relative vapor density2.97 (vs air)
- r) Particle characteristicsNo data available
- s) Explosive propertiesNo data available
- t) Oxidizing propertiesNo data available
- SolubilityIn methanol: 590 and 800 g/L at 5 and 10 °C, respectively. Miscible at higher temperatures (Kiser et al., 1961). Miscible with other aliphatic hydrocarbons, e.g., pentane, hexane, heptane, etc.
- Henry's Law Constant1.69(atmm3/mol) at 25 °C (Mackay and Shiu, 1981)
- Dielectric constant1.8700000000000001
9.2 Other safety information
Relative vapor density2.98 - (Air = 1.0)
10.1 Chemical stability
The product is chemically stable under standard ambient conditions (room temperature) .
10.2 Possibility of hazardous reactions
No data available
10.3 Conditions to avoid
Warming.
10.4 Incompatible materials
Oxidizing agents
10.5 Hazardous decomposition products
In the event of fire: see section 5
11.1 Information on toxicological effects
Acute toxicityOral: No data available
Inhalation: No data available
Dermal: No data available
Skin corrosion/irritation
Inhalation: No data available
Dermal: No data available
Remarks: No data available
Serious eye damage/eye irritation
Remarks: No data available
Respiratory or skin sensitization
Classified based on available data. For more details, see section 2
Germ cell mutagenicity
Classified based on available data. For more details, see section 2
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
May cause drowsiness or dizziness.
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
The substance or mixture is known to cause human aspiration toxicity hazards or has to be regarded as if it causes a human aspiration toxicity hazard.
11.2 Additional Information
RTECS: EJ9300000
Dermatitis, Blurred vision, Effects due to ingestion may include:, Central nervous system depression, Lung irritation
Dermatitis, Blurred vision, Effects due to ingestion may include:, Central nervous system depression, Lung irritation
12.1 Toxicity
No data available
12.2 Persistence and degradability
No data available
12.3 Bioaccumulative potential
No data available
12.4 Mobility in soil
No data available
12.5 Results of PBT and vPvB assessment
PBT/vPvB assessment not available as chemical safety assessment not required/not conducted
12.6 Endocrine disrupting properties
No data available
12.7 Other adverse effects
No data available
13.1 Waste treatment methods
Product
Offer surplus and non-recyclable solutions to a licensed disposal company.
Offer surplus and non-recyclable solutions to a licensed disposal company.
14.1 UN number
ADR/RID: 1208
IMDG: 1208
IATA-DGR: 1208
IMDG: 1208
IATA-DGR: 1208
14.2 UN proper shipping name
ADR/RID: HEXANES
IMDG: HEXANES
IATA-DGR: Hexanes
IMDG: HEXANES
IATA-DGR: Hexanes
14.3 Transport hazard class(es)
ADR/RID: 3
IMDG: 3
IATA-DGR: 3
IMDG: 3
IATA-DGR: 3
14.4 Packaging group
ADR/RID: II
IMDG: II
IATA-DGR: II
IMDG: II
IATA-DGR: II
14.5 Environmental hazards
ADR/RID: yes
IMDG Marine pollutant: yes
IATA-DGR: no
IMDG Marine pollutant: yes
IATA-DGR: no
14.6 Special precautions for user
Based on chemical properties, choose appropriate tools and conditions of transport.
Transporting tools shall be equipped with appropriate and sufficient firefighting equipment and emergency leaking installations. If transporting by road, please go along the specified route.
Transporting tools shall be equipped with appropriate and sufficient firefighting equipment and emergency leaking installations. If transporting by road, please go along the specified route.
14.7 Incompatible materials
Oxidizing agents
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture
National regulatory information
Law on the Prevention and Control of Occupational Diseases
Regulations on Safety Management of Hazardous Chemicals
Catalogue of Hazardous Chemicals : Listed
Other regulations
Please pay attention on the waste treatment should also comply with local regulations requirement.
Law on the Prevention and Control of Occupational Diseases
Regulations on Safety Management of Hazardous Chemicals
Catalogue of Hazardous Chemicals : Listed
Other regulations
Please pay attention on the waste treatment should also comply with local regulations requirement.
Abbreviations and acronyms
CAS: Chemical Abstracts Service
TWA: Time-Weighted Average
STEL: Short-Term Exposure Limit
LD50: Lethal Dose 50%
LC50: Lethal Concentration 50%
EC50: Effective Concentration 50%
PEL: Permissible Exposure Limit
TLV: Threshold Limit Value
IMDG: International Maritime Dangerous Goods Code
IATA: International Air Transport Association
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
DOT: US Department of Transportation
NFPA: National Fire Protection Association
NIOSH: National Institute for Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
TWA: Time-Weighted Average
STEL: Short-Term Exposure Limit
LD50: Lethal Dose 50%
LC50: Lethal Concentration 50%
EC50: Effective Concentration 50%
PEL: Permissible Exposure Limit
TLV: Threshold Limit Value
IMDG: International Maritime Dangerous Goods Code
IATA: International Air Transport Association
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
DOT: US Department of Transportation
NFPA: National Fire Protection Association
NIOSH: National Institute for Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
Disclaimer:
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.