Chemical Safety Data Sheet MSDS / SDS
FUSARENON X
Revision Date:2026-03-20Revision Number:1
Product identifier
- Product name: FUSARENON X
- CBnumber: CB1503492
- CAS: 23255-69-8
- EINECS Number: 621-752-1
- Synonyms: -en-8-one ;Fusarenon
Relevant identified uses of the substance or mixture and uses advised against
- Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
- Uses advised against: none
Company Identification
- Company: Chemicalbook
- Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
- Telephone: 010-86108875
GHS Label elements, including precautionary statements
-
Symbol(GHS)
- Signal wordDanger
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
P302+P352 IF ON SKIN: wash with plenty of soap and water.
Hazard statements
H335 May cause respiratory irritation
H319 Causes serious eye irritation
H315 Causes skin irritation
H300 Fatal if swallowed
Substance
- Product name: FUSARENON X
- Synonyms: -en-8-one ;Fusarenon
- CAS: 23255-69-8
- EC number: 621-752-1
- MF: C17H22O8
- MW: 354.36
Description of first aid measures
General information
Immediately remove any clothing soiled by the product.
Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.
Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48 hours after the accident.
After inhalation
In case of unconsciousness place patient stably in side position for transportation.
After skin contact
Immediately wash with water and soap and rinse thoroughly.
After eye contact
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
After swallowing
Immediately call a doctor.
Information for doctor
Most important symptoms and effects, both acute and delayed
No further relevant information available.
Indication of any immediate medical attention and special treatment needed
No further relevant information available.
FIRE-FIGHTING MEASURES
| Fire-fighting measure | Details |
|---|---|
| Suitable extinguishing agents | Use fire fighting measures that suit the environment. A solid water stream may be inefficient. |
| Special hazards arising from the substance or mixture | 67-56-1During heating or in case of fire poisonous gases are produced. |
| Protective equipment | Mouth respiratory protective device. |
NFPA 704
2
0
0
| HEALTH | 2 | Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine) | |
| FIRE | 0 | Materials that will not burn under typical fire conditions, including intrinsically noncombustible materials such as concrete, stone, and sand. Materials that will not burn in air when exposed to a temperature of 820 °C (1,500 °F) for a period of 5 minutes.(e.g. Carbon tetrachloride) | |
| REACT | 0 | Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2) | |
| SPEC. HAZ. |
Personal precautions, protective equipment and emergency procedures
Mount respiratory protective device.
Environmental precautions
Do not allow to enter sewers/ surface or ground water.
Methods and material for containment and cleaning up
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Dispose contaminated material as waste according to section 13.
Ensure adequate ventilation.
Dispose contaminated material as waste according to section 13.
Ensure adequate ventilation.
Reference to other sections
See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.
Protective Action Criteria for Chemicals
PAC-1
75-09-2 Dichloromethane 200 ppm
PAC-2
75-09-2 Dichloromethane 560 ppm
PAC-3
Handling
Precautions for safe handling
Ensure good ventilation/exhaustion at the workplace.
Open and handle receptacle with care.
Prevent formation of aerosols.
Open and handle receptacle with care.
Prevent formation of aerosols.
Information about protection against explosions and fires
Keep respiratory protective device available.
Conditions for safe storage, including any incompatibilities
Storage
Store in accordance with information listed on the product insert.
Requirements to be met by storerooms and receptacles
No special requirements.
Information about storage in one common storage facility
Not required.
Further information about storage conditions
Keep receptacle tightly sealed.
Specific end use(s)
No further relevant information available.
Additional information about design of technical systems
No further data; see section 7.
Control parameters
Components with limit values that require monitoring at the workplace:
| 75-09-2 Dichloromethane | |
|---|---|
| PEL | Short-term value: 125 ppm Long-term value: 25 ppm see 29 CFR 1910.1052 |
| REL | See Pocket Guide App. A |
| TLV | Long-term value: 50 ppm |
| BEI | , A3 |
| Ingredients with biological limit values: | |
| 75-09-2 Dichloromethane | |
|---|---|
| BEI | 0.3 mg/L Medium: urine Time: end of shift Parameter: Dichloromethane (semi-quantitative) |
Additional information
The lists that were valid during the creation were used as basis.
Exposure controls
Personal protective equipment
General protective and hygienic measures
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Store protective clothing separately.
Avoid contact with the eyes and skin.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Store protective clothing separately.
Avoid contact with the eyes and skin.
Breathing equipment
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use respiratory protective device that is independent of circulating air.
Protection of hands
Protective gloves
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation
Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application.
Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Eye protection
Safety glasses
Tightly sealed goggles
Tightly sealed goggles
Information on basic physicochemical properties
- Other informationNo information available
- Solids content0.1 %
- VOC content0.00 % 0.0 g/l / 0.00 lb/gal
- Organic solvents100.0 %
- SOLUBILITYDichloromethane: Soluble
- KinematicNot determined.
- Dynamicat 20 °C (68 °F): 0.43 mPas
- Partition coefficient (n-octanol/water)Not determined.
- Water at 20 °C (68 °F)20 g/l
- Solubility in / Miscibility withDichloromethane: Soluble
- Evaporation RateNot determined.
- Vapor DensityNot determined.
- Relative Density1.2646 (rough estimate)
- Density at 20 °C (68 °F)1.33 g/cm³ (11.09885 lbs/gal)
- Vapor Pressure at 20 °C (68 °F)453 hPa (339.8 mm Hg)
- Explosion limitsLower: 13 Vol %
Upper: 22 Vol % - Danger of explosionProduct does not present an explosion hazard.
- Ignition temperatureProduct is not selfigniting.
- Decomposition temperatureNot determined.
- Auto igniting605 °C (1,121 °F)
- Flammability (solid,gas)Not applicable.
- Flash point2 °C
- Boiling point/Boiling range40 °C (104 °F)
- Melting point/Melting range-95.1 °C (-139.2 °F)
- pHNot determined.
- FormulationA solution in dichloromethane
- Odor ThresholdNot determined.
- Molecular Weight354.4 g/mol
- Structural FormulaC17H22O8
- OdorLike chlorine
- ColorColorless
- Physical StateLiquid
Reactivity
No further relevant information available.
Chemical stability
Thermal decomposition / conditions to be avoided
No decomposition if used according to specifications.
Possibility of hazardous reactions
No dangerous reactions known.
Conditions to avoid
No further relevant information available.
Incompatible materials
No further relevant information available.
Hazardous decomposition products
No dangerous decomposition products known.
Information on toxicological effects
Acute toxicity
LD/LC50 values that are relevant for classification:
| Substance / Estimate | Route | Endpoint | Value |
|---|---|---|---|
| ATE (Acute Toxicity Estimate) | Oral | LD50 | 1,601 mg/kg (rat) |
| 75-09-2 Dichloromethane | Oral | LDLO | 357 mg/kg (hmn) |
| 75-09-2 Dichloromethane | Oral | LD50 | 1,600 mg/kg (rat) |
| 75-09-2 Dichloromethane | Oral | TDLO | 1,429 µL/kg (man) |
| 75-09-2 Dichloromethane | Inhalative | LC50/4 h | 88 mg/l (rat) |
| 75-09-2 Dichloromethane | Intraperitoneal | LD50 | 916 mg/kg (rat) |
| 75-09-2 Dichloromethane | Subcutaneous | LD50 | 6,460 mg/kg (mouse) |
Primary irritant effect
on the skin
Irritant to skin and mucous membranes.
on the eye
Irritating effect.
Sensitization
No sensitizing effects known.
Additional toxicological information
The product shows the following dangers according to internally approved calculation methods for preparations
Harmful
Irritant
Harmful
Irritant
Carcinogenic categories
IARC (International Agency for Research on Cancer)
75-09-2 Dichloromethane 2A
NTP (National Toxicology Program)
75-09-2 Dichloromethane R
OSHA-Ca (Occupational Safety & Health Administration)
75-09-2 Dichloromethane
Toxicity
Aquatic toxicity
No further relevant information available.
Persistence and degradability
No further relevant information available.
Behavior in environmental systems
Bioaccumulative potential
No further relevant information available.
Mobility in soil
No further relevant information available.
Additional ecological information
General notes
Water hazard class 2 (Self-assessment) hazardous for water
Do not allow product to reach ground water, water course or sewage system.
Danger to drinking water if even small quantities leak into the ground.
Do not allow product to reach ground water, water course or sewage system.
Danger to drinking water if even small quantities leak into the ground.
Results of PBT and vPvB assessment
PBT
Not applicable.
vPvB
Not applicable.
PBT:
Not applicable.
vPvB:
Not applicable.
Other adverse effects
No further relevant information available.
Waste treatment methods
Recommendation
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
Uncleaned packagings
Recommendation
Disposal must be made according to official regulations.
UN-Number
DOT, IMDG, IATA UN1593
UN proper shipping name
DOT, IATA Dichloromethane
IMDG DICHLOROMETHANE
IMDG DICHLOROMETHANE
Transport hazard class(es)
DOTClass: 6.1 Toxic substances
Label: 6.1
IMDG, IATA
Label: 6.1
Class: 6.1 Toxic substances
Label: 6.1
Label: 6.1
Packing group
DOT, IMDG, IATA III
Environmental hazards
Not applicable.
Special precautions for user
Warning: Toxic substances
Hazard identification number (Kemler code)
60
EMS Number
F-A,S-A
Segregation groups
(SGG10) Liquid halogenated hydrocarbons
Stowage Category
A
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
Not applicable.
Transport/Additional information
DOT:
Quantity limitations
On passenger aircraft/rail: 60 L
On cargo aircraft only: 220 L
On cargo aircraft only: 220 L
IMDG:
Limited quantities (LQ)
5L
Excepted quantities (EQ)
Code: E1
Maximum net quantity per inner packaging: 30 ml
Maximum net quantity per outer packaging: 1000 ml
Maximum net quantity per inner packaging: 30 ml
Maximum net quantity per outer packaging: 1000 ml
IATA:
Remarks
When sold in quantities of less than or equal to 1 mL, or 1 g, with an Excepted Quantity Code of
E1, E2, E4, or E5, this item meets the De Minimis
Quantities exemption, per IATA 2.6.10.
Therefore packaging does not have to be labeled as
Dangerous Goods/Excepted Quantity.
E1, E2, E4, or E5, this item meets the De Minimis
Quantities exemption, per IATA 2.6.10.
Therefore packaging does not have to be labeled as
Dangerous Goods/Excepted Quantity.
UN "Model Regulation"
UN 1593 DICHLOROMETHANE, 6.1, III
Safety, health and environmental regulations/legislation specific for the substance or mixture
This chemical/product is not and cannot be distributed in commerce (as defined in TSCA section 3(5))
Sara
| Section 355 (extremely hazardous substances): | None of the ingredients is listed. |
| Section 313 (Specific toxic chemical listings): | 75-09-2 Dichloromethane |
| TSCA (Toxic Substances Control Act): | This chemical/product is not and cannot be distributed in commerce (as defined in TSCA section 3(5)) |
| or processed (as defined in TSCA section 3(13)) for consumer paint or coating removal. | |
| 75-09-2 Dichloromethane ACTIVE | |
| Hazardous Air Pollutants 75-09-2 Dichloromethane | |
Proposition 65
| Chemicals known to cause cancer: | 75-09-2 Dichloromethane |
| Chemicals known to cause reproductive toxicity for females: | None of the ingredients is listed. |
| Chemicals known to cause reproductive toxicity for males: | None of the ingredients is listed. |
| Chemicals known to cause developmental toxicity: | None of the ingredients is listed. |
Carcinogenic categories
| EPA (Environmental Protection Agency): |
75-09-2
Dichloromethane L
TLV (Threshold Limit Value)
75-09-2
Dichloromethane A3
75-09-2
Dichloromethane
Chemical safety assessment
A Chemical Safety Assessment has not been carried out.
Abbreviations and acronyms
IMDG: International Maritime Code for Dangerous Goods
DOT: US Department of Transportation
IATA: International Air Transport Association
EINECS: European Inventory of Existing Commercial Chemical Substances
ELINCS: European List of Notified Chemical Substances
CAS: Chemical Abstracts Service (division of the American Chemical Society)
NFPA: National Fire Protection Association (USA)
HMIS: Hazardous Materials Identification System (USA)
VOC: Volatile Organic Compounds (USA, EU)
LC50: Lethal concentration, 50 percent
LD50: Lethal dose, 50 percent
PBT: Persistent, Bioaccumulative and Toxic vPvB: very Persistent and very Bioaccumulative
NIOSH: National Institute for Occupational Safety
OSHA: Occupational Safety & Health
TLV: Threshold Limit Value
PEL: Permissible Exposure Limit
REL: Recommended Exposure Limit
BEI: Biological Exposure Limit
Acute Toxicity - Oral 4: Acute toxicity – Category 4
Skin Irritation 2: Skin corrosion/irritation – Category 2
Eye Irritation 2A: Serious eye damage/eye irritation – Category 2A
Germ Cell Mutagenicity 2: Germ cell mutagenicity – Category 2
Carcinogenicity 2: Carcinogenicity – Category 2
Specific Target Organ Toxicity - Single Exposure 3: Specific target organ toxicity (single exposure) – Category 3
Specific Target Organ Toxicity - Repeated Exposure 1: Specific target organ toxicity (repeated exposure) – Category 1
DOT: US Department of Transportation
IATA: International Air Transport Association
EINECS: European Inventory of Existing Commercial Chemical Substances
ELINCS: European List of Notified Chemical Substances
CAS: Chemical Abstracts Service (division of the American Chemical Society)
NFPA: National Fire Protection Association (USA)
HMIS: Hazardous Materials Identification System (USA)
VOC: Volatile Organic Compounds (USA, EU)
LC50: Lethal concentration, 50 percent
LD50: Lethal dose, 50 percent
PBT: Persistent, Bioaccumulative and Toxic vPvB: very Persistent and very Bioaccumulative
NIOSH: National Institute for Occupational Safety
OSHA: Occupational Safety & Health
TLV: Threshold Limit Value
PEL: Permissible Exposure Limit
REL: Recommended Exposure Limit
BEI: Biological Exposure Limit
Acute Toxicity - Oral 4: Acute toxicity – Category 4
Skin Irritation 2: Skin corrosion/irritation – Category 2
Eye Irritation 2A: Serious eye damage/eye irritation – Category 2A
Germ Cell Mutagenicity 2: Germ cell mutagenicity – Category 2
Carcinogenicity 2: Carcinogenicity – Category 2
Specific Target Organ Toxicity - Single Exposure 3: Specific target organ toxicity (single exposure) – Category 3
Specific Target Organ Toxicity - Repeated Exposure 1: Specific target organ toxicity (repeated exposure) – Category 1
Disclaimer:
The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.
Recommended Products
trans-1,2-Cyclopentanediol SDS
Ethylhexylglycerin SDS
FUSARENON X SDS
3-METHYL-2-CYCLOHEXEN-1-OL SDS
1,2-EPOXY-7-OCTENE SDS
2-METHYL-2-CYCLOHEXEN-1-ONE SDS
(TETRAHYDRO-PYRAN-3-YL)-METHANOL SDS
(R)-(-)-Methyl glycidyl ether SDS
(TETRAHYDRO-2H-PYRAN-4-YL)METHANOL SDS
(S)-2-Methyl Glycidol SDS