Chemical Safety Data Sheet MSDS / SDS

Sodium chloroacetate

Revision Date:2023-12-07Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

  • Product name: Sodium chloroacetate
  • CBnumber: CB9853591
  • CAS: 3926-62-3
  • EINECS Number: 223-498-3
  • Synonyms: SODIUM MONOCHLOROACETATE,SMA

Relevant identified uses of the substance or mixture and uses advised against

  • Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
  • Uses advised against: none

Company Identification

  • Company: Chemicalbook
  • Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
  • Telephone: 400-158-6606

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

  • Symbol(GHS)
  • Signal wordDanger
Precautionary statements
P273 Avoid release to the environment.
P301+P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continuerinsing.
P321 Specific treatment (see … on this label).
P332+P313 IF SKIN irritation occurs: Get medical advice/attention.
P405 Store locked up.
Hazard statements
H301 Toxic if swalloed
H315 Causes skin irritation
H319 Causes serious eye irritation
H400 Very toxic to aquatic life

SECTION 3: Composition/information on ingredients

Substance

  • Product name: Sodium chloroacetate
  • Synonyms: SODIUM MONOCHLOROACETATE,SMA
  • CAS: 3926-62-3
  • EC number: 223-498-3
  • MF: C2H2ClNaO2
  • MW: 116.48

SECTION 4: First aid measures

Description of first aid measures

General advice
Show this material safety data sheet to the doctor in attendance.
If inhaled
After inhalation: fresh air.
In case of skin contact
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower.
In case of eye contact
After eye contact: rinse out with plenty of water. Call in ophthalmologist. Remove contact lenses.
If swallowed
If swallowed: give water to drink (two glasses at most). Seek medical advice immediately. In exceptional cases only, if medical care is not available within one hour, induce vomiting (only in persons who are wide awake and fully conscious), administer activated charcoal (20 - 40 g in a 10% slurry) and consult a doctor as quickly as possible.

Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11

Indication of any immediate medical attention and special treatment needed

No data available

SECTION 5: Firefighting measures

Extinguishing media

Suitable extinguishing media
Water Foam Carbon dioxide (CO2) Dry powder
Unsuitable extinguishing media
For this substance/mixture no limitations of extinguishing agents are given.

Special hazards arising from the substance or mixture

Carbon oxides Hydrogen chloride gas Sodium oxides Combustible.

Vapors are heavier than air and may spread along floors. Forms explosive mixtures with air on intense heating.

Development of hazardous combustion gases or vapours possible in the event of fire.

Advice for firefighters

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

Further information

Suppress (knock down) gases/vapors/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.

NFPA 704

3
1
1
HEALTH 3 Short exposure could cause serious temporary or moderate residual injury (e.g. liquid hydrogen, sulfuric acid, calcium hypochlorite, hexafluorosilicic acid)
FIRE 1 Materials that require considerable preheating, under all ambient temperature conditions, before ignition and combustion can occur. Includes some finely divided suspended solids that do not require heating before ignition can occur. Flash point at or above 93.3 °C (200 °F). (e.g. mineral oil, ammonia)
REACT 1 Normally stable, but can become unstable at elevated temperatures and pressures (e.g. propene)
SPEC. HAZ.

SECTION 6: Accidental release measures

Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Avoid inhalation of dusts. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert.

For personal protection see section 8.

Environmental precautions

Do not let product enter drains.

Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully. Dispose of properly. Clean up affected area. Avoid generation of dusts.

Reference to other sections

For disposal see section 13.

SECTION 7: Handling and storage

Precautions for safe handling

For precautions see section 2.2.

Conditions for safe storage, including any incompatibilities

Storage conditions

Tightly closed. Dry. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorized persons.

Specific end use(s)

Apart from the uses mentioned in section 1.2 no other specific uses are stipulated

SECTION 8: Exposure controls/personal protection

control parameter

Hazard composition and occupational exposure limits
Does not contain substances with occupational exposure limits.

Exposure controls

Personal protective equipment
Eye/face protection

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses

Skin protection

This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Full contact

Material: Nitrile rubber

Minimum layer thickness: 0,11 mm Break through time: 480 min

Material tested:KCL 741 Dermatril? L

This recommendation applies only to the product stated in the safety data sheet, supplied by us and for the designated use. When dissolving in or mixing with other substances and under conditions deviating from those stated in EN374 please contact the supplier of CE-approved gloves (e.g. KCL GmbH, D-36124 Eichenzell, Internet: www.kcl.de).

Splash contact Material: Nitrile rubber

Minimum layer thickness: 0,11 mm Break through time: 480 min

Material tested:KCL 741 Dermatril? L

Body Protection

protective clothing

Respiratory protection

required when dusts are generated.

Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.

Recommended Filter type: Filter type P3

The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer.

These measures have to be properly documented.

Control of environmental exposure

Do not let product enter drains.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

  • Appearancewhite powder
  • OdourNo data available
  • Odour ThresholdNo data available
  • pH4.5-9.0 (50g/l, H2O, 20℃)
  • Melting point/freezing pointMelting point/range: 199 °C - dec.
  • Initial boiling point and boiling rangeNo data available
  • Flash point270 °C - c.c.
  • Evaporation rateNo data available
  • Flammability (solid, gas)The product is not flammable.
  • Upper/lower flammability or explosive limitsNo data available
  • Vapour pressure< 0,1 hPa at 20 °C - OECD Test Guideline 104
  • Vapour density No data available
  • Relative densityNo data available 1,87 at 20 °C - OECD Test Guideline 109
  • Water solubility822 g/l at 20,1 °C - OECD Test Guideline 105- completely soluble
  • Partition coefficient: n-octanol/waterlog Pow: -3,8 at 20 °C - OECD Test Guideline 107 - Bioaccumulation is not expected.
  • Autoignition temperaturedoes not ignite
  • Decomposition temperatureNo data available
  • ViscosityViscosity, kinematic: No data available Viscosity, dynamic: No data available
  • Explosive propertiesNo data available
  • Oxidizing propertiesNo data available

Other safety information

Surface tension 73,2 mN/m at 1g/l at 20 °C

  • OECD Test Guideline 115

    Dissociation constant 2,8 at 20 °C

  • OECD Test Guideline 112

SECTION 10: Stability and reactivity

Reactivity

Forms explosive mixtures with air on intense heating.

A range from approx. 15 Kelvin below the flash point is to be rated as critical.

The following applies in general to flammable organic substances and mixtures: in correspondingly fine distribution, when whirled up a dust explosion potential may generally be assumed.

Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

Possibility of hazardous reactions

Violent reactions possible with:

Strong oxidizing agents alkali hydroxides


Conditions to avoid

Strong heating.

Incompatible materials

Strong oxidizing agents

Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

Information on toxicological effects

Acute toxicity
LD50 Oral - Rat - female - 90,4 mg/kg
(OECD Test Guideline 401) Symptoms: Nausea, Vomiting
LC50 Inhalation - Rat - male and female - 4 h - > 1.268 mg/m3 (OECD Test Guideline 403)
LD50 Dermal - Rat - female - > 2.000 mg/kg (OECD Test Guideline 402)
Skin corrosion/irritation
Causes skin irritation. Classified according to Regulation (EU) 1272/2008, Annex VI (Table 3.1/3.2)
Serious eye damage/eye irritation
Eyes - Rabbit
Result: Irritating to eyes. - 24 h
(Regulation (EC) No. 440/2008, Annex, B.5)
Respiratory or skin sensitization
(OECD Test Guideline 429)
Germ cell mutagenicity
Test Type: Ames test
Test system: S. typhimurium
Metabolic activation: with and without metabolic activation
Method: OECD Test Guideline 471 Result: negative
Test Type: In vitro mammalian cell gene mutation test Test system: mouse lymphoma cells
Metabolic activation: without metabolic activation Result: positive
Remarks: (ECHA)
Test Type: Chromosome aberration test in vitro Test system: Chinese hamster ovary cells
Metabolic activation: with and without metabolic activation Result: negative
Remarks: (ECHA)
Test Type: Chromosome aberration test Species: Rat
Cell type: Bone marrow Application Route: Intraperitoneal Method: OECD Test Guideline 475 Result: positive
Test Type: in vivo assay Species: Mouse
Cell type: Liver cells Application Route: Oral
Result: negative Remarks: (ECHA)
Carcinogenicity
No data available
Reproductive toxicity
No data available
Specific target organ toxicity - single exposure
No data available
Specific target organ toxicity - repeated exposure
No data available
Aspiration hazard
No data available
Toxicity
LD50 orally in Rabbit: 95 mg/kg LD50 dermal Rat > 2000 mg/kg

SECTION 12: Ecological information

Toxicity

Toxicity to fish
static test LC50 - Poecilia reticulata (guppy) - 369 mg/l - 96 h Remarks: (ECHA)


Toxicity to daphnia and other aquatic invertebrates

static test EC50 - Daphnia magna (Water flea) - 74,2 mg/l - 48 h (OECD Test Guideline 202)

Toxicity to algae
static test ErC50 - Desmodesmus subspicatus (green algae) - 0,033 mg/l - 72 h

(OECD Test Guideline 201)

Persistence and degradability

Biodegradability aerobic - Exposure time 28 d

Result: 69 % - Readily biodegradable. Remarks: (ECHA)


Bioaccumulative potential

No data available

Mobility in soil

No data available

Results of PBT and vPvB assessment

This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.

Other adverse effects

Discharge into the environment must be avoided.

SECTION 13: Disposal considerations

Waste treatment methods

Product

See www.retrologistik.com for processes regarding the return of chemicals and

containers, or contact us there if you have further questions.

SECTION 14: Transport information

UN number

ADR/RID: 2659 IMDG: 2659 IATA: 2659

UN proper shipping name


ADR/RID: SODIUM CHLOROACETATE IMDG: SODIUM CHLOROACETATE


IATA: Sodium chloroacetate

14.3

Transport hazard class(es)

ADR/RID: 6.1 IMDG: 6.1


IATA: 6.1

14.4

Packaging group

ADR/RID: III IMDG: III


IATA: III

14.5

Environmental hazards

ADR/RID: yes IMDG Marine pollutant: yes


IATA: no

14.6

Special precautions for user

No data available


SECTION 15: Regulatory information

Safety, health and environmental regulations/legislation specific for the substance or mixture

Regulations on the Safety Management of Hazardous Chemicals
China Catalog of Hazardous chemicals 2015:Listed. website: https://www.mem.gov.cn/
Measures for Environmental Management of New Chemical Substances
Vietnam National Chemical Inventory:Listed. website: https://chemicaldata.gov.vn/
United States Toxic Substances Control Act (TSCA) Inventory:Listed. website: https://www.epa.gov/
Philippines Inventory of Chemicals and Chemical Substances (PICCS):Listed. website: https://emb.gov.ph/
New Zealand Inventory of Chemicals (NZIoC):Listed. website: https://www.epa.govt.nz/
Korea Existing Chemicals List (KECL):Listed. website: http://ncis.nier.go.kr
European Inventory of Existing Commercial Chemical Substances (EINECS):Listed. website: https://echa.europa.eu/
EC Inventory:Listed.
Chinese Chemical Inventory of Existing Chemical Substances (China IECSC):Listed. website: https://www.mee.gov.cn/

SECTION 16: Other information

Abbreviations and acronyms

  • ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
  • CAS: Chemical Abstracts Service
  • EC50: Effective Concentration 50%
  • IATA: International Air Transportation Association
  • IMDG: International Maritime Dangerous Goods
  • LC50: Lethal Concentration 50%
  • LD50: Lethal Dose 50%
  • RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
  • STEL: Short term exposure limit
  • TWA: Time Weighted Average

References

【1】CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple

【2】ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp

【3】ECHA - European Chemicals Agency, website: https://echa.europa.eu/

【4】eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en

【5】ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg

【6】Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp

【7】HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm

【8】IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/

【9】IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home

【10】Sigma-Aldrich, website: https://www.sigmaaldrich.com/

Other Information

See ICSC 0235.Specific treatment is necessary in case of poisoning with this substance; the appropriate means with instructions must be available.Sodium dichloroacetate is a potential antidote.Consult a poison information centre or an expert for further information.
Disclaimer:

The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.

Recommended Products
Sodium dichloroacetate SDS SODIUM TRICHLOROACETATE SDS Sodium chlorodifluoroacetate SDS Sodium acetate trihydrate SDS alpha-Methylcinnamylaldehyde SDS Acetic acid, chloro-, sodium salt, reaction products with 4,5-dihydro-1H-imidazole-1-ethanol 2-norcoco alkyl derivs. and sodium hydroxide SDS ALPHA,BETA-DICHLOROISOBUTYRIC ACID SODIUM SALT SDS 2,2-DICHLOROPROPIONIC ACID SODIUM SALT SDS Sodium chloroacetate SDS