Chemical Safety Data Sheet MSDS / SDS

Ammonium thioglycolate

Revision Date:2026-03-21Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

  • Product name: Ammonium thioglycolate
  • CBnumber: CB5445341
  • CAS: 5421-46-5
  • EINECS Number: 226-540-9
  • Synonyms: mercapto-aceticacimonoammoniumsalt ;thiofacoa-50

Relevant identified uses of the substance or mixture and uses advised against

  • Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
  • Uses advised against: none

Company Identification

  • Company: Chemicalbook
  • Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
  • Telephone: 010-86108875

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

  • Symbol(GHS)
  • Signal wordDanger
Precautionary statements
P302+P352 IF ON SKIN: wash with plenty of soap and water.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
Hazard statements
H317 May cause an allergic skin reaction
H301 Toxic if swalloed
H290 May be corrosive to metals

SECTION 3: Composition/information on ingredients

Substance

  • Product name: Ammonium thioglycolate
  • Synonyms: mercapto-aceticacimonoammoniumsalt ;thiofacoa-50
  • CAS: 5421-46-5
  • EC number: 226-540-9
  • MF: C2H4O2S.H3N
  • MW: 109.15

SECTION 4: First aid measures

General advice

Show this safety data sheet to the doctor in attendance.

If inhaled

After inhalation: fresh air.

In case of skin contact

In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician.

In case of eye contact

After eye contact: rinse out with plenty of water. Remove contact lenses.

If swallowed

If swallowed: give water to drink (two glasses at most). Seek medical advice immediately. In exceptional cases only, if medical care is not available within one hour, induce vomiting (only in persons who are wide awake and fully conscious), administer activated charcoal (20 - 40 g in a 10% slurry) and consult a doctor as quickly as possible.

Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2) and/or in section 11

Protection of first-aiders

For personal protection see section 8.

Notes to physician

No data available

SECTION 5: Firefighting measures

Suitable extinguishing media

Water Foam Carbon dioxide (CO2) Dry powder

Unsuitable extinguishing media

For this substance/mixture no limitations of extinguishing agents are given.

Specific hazards during fire fighting

Mixture with combustible ingredients. Development of hazardous combustion gases or vapours possible in the event of fire.

Hazardous combustion products

Carbon oxides Nitrogen oxides (NOx) Sulphur oxides

Specific extinguishing methods

Suppress (knock down) gases/vapours/mists with a water spray jet. Prevent fire extinguishing water from contaminating surface water or the ground water system.

Special protective equipment for fire-fighters

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

NFPA 704

2
0
0
HEALTH 2 Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine)
FIRE 0 Materials that will not burn under typical fire conditions, including intrinsically noncombustible materials such as concrete, stone, and sand. Materials that will not burn in air when exposed to a temperature of 820 °C (1,500 °F) for a period of 5 minutes.(e.g. Carbon tetrachloride)
REACT 0 Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2)
SPEC. HAZ.

SECTION 6: Accidental release measures

Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Do not breathe vapours, aerosols. Avoid substance contact. Ensure adequate ventilation. Evacuate the danger area, observe emergency procedures, consult an expert. Advice for emergency responders: For personal protection see section 8.

Environmental precautions

Do not let product enter drains.

Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up carefully with liquid-absorbent material . Dispose of properly. Clean up affected area.

SECTION 7: Handling and storage

Handling

Avoidance of contact
Strong oxidizing agents Metals

Storage

Conditions for safe storage
No metal containers.
Further information on storage conditions
Tightly closed. Keep in a well-ventilated place. Keep locked up or in an area accessible only to qualified or authorised persons.
Storage class
6.1C, Combustible, acute toxic Cat.3 / toxic compounds or compounds which causing chronic effects
Recommended storage temperature
Recommended storage temperature see product label.

SECTION 8: Exposure controls/personal protection

control parameter

Hazard composition and occupational exposure limits
Does not contain substances with occupational exposure limits.

Engineering measures

No data available

Personal protective equipment

Respiratory protection
required when vapours/aerosols are generated.
Our recommendations on filtering respiratory protection are based on the following standards: DIN EN 143, DIN 14387 and other accompanying standards relating to the used respiratory protection system.
Recommended Filter type
Filter type ABEK
The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer. These measures have to be properly documented.
Eye/face protection
Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Safety glasses
Skin and body protection
protective clothing
Hand protection
Material
Nitrile rubber
Break through time
480 min
Glove thickness
0.11 mm
Protective index
Full contact
Manufacturer
(KCL 740 / Aldrich Z677272, Size M)
Material
Nitrile rubber
Break through time
480 min
Glove thickness
0.11 mm
Protective index
Splash contact
Manufacturer
(KCL 740 / Aldrich Z677272, Size M)
Manufacturer
data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374
Remarks
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.
The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.
If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the CE approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.
Hygiene measures
Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

  • Density1.190 g/cm3
  • Water solubilitysoluble (20 °C)
  • Partition coefficient: n-octanol/waterNo data available
  • Autoignition temperatureNo data available
  • Decomposition temperatureNo data available
  • Viscosity, dynamicNo data available
  • Viscosity, kinematicNo data available
  • Flow timeNo data available
  • Particle characteristics Particle sizeNo data available
  • Molecular weight109.15 g/mol
  • Oxidizing propertiesnone
  • Explosive propertiesNot classified as explosive.
  • Relative density1.22
  • Relative vapor densityNo data available
  • Vapor pressure0.001Pa at 25℃
  • Lower explosion limit / Lower flammability limitNo data available
  • Upper explosion limit / Upper flammability limitNo data available
  • Burning rateNo data available
  • Flammability (liquids)No data available
  • Flammability (solid, gas)No data available
  • Evaporation rateNo data available
  • Flash pointNo data available
  • Boiling point/boiling range115℃[at 101 325 Pa]
  • Melting point/ rangeNo data available
  • pHca. 6 (20 °C)
  • Odor ThresholdNo data available
  • Odorstrong skunk-like odor
  • Colorcolourless
  • Appearanceclear, liquid
  • Viscosity9.06mm2/s
  • Physical stateSolution

SECTION 10: Stability and reactivity

Reactivity

No data available

Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

Possibility of hazardous reactions

No data available

Conditions to avoid

no information available

Incompatible materials

Strong oxidizing agents Metals

Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

11.1 Information on toxicological effects

Mixture Acute toxicity
Oral: No data available
Inhalation: No data available
Acute toxicity estimate Dermal - 4,546 mg/kg (Calculation method)
Skin corrosion/irritation
Classified based on available data. For more details, see section 2
Serious eye damage/eye irritation
Classified based on available data. For more details, see section 2
Respiratory or skin sensitization
Mixture may cause an allergic skin reaction.
Germ cell mutagenicity
Classified based on available data. For more details, see section 2
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
Classified based on available data. For more details, see section 2
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
Classified based on available data. For more details, see section 2

11.2 Additional Information

To the best of our knowledge, the chemical, physical, and toxicological properties have not been thoroughly investigated.
Other dangerous properties can not be excluded.
Handle in accordance with good industrial hygiene and safety practice.
Components Ammonium thioglycolate
Acute toxicity
LD50 Oral - Rat - male and female - 35 - 142 mg/kg (OECD Test Guideline 423)
Remarks: (ECHA)
Inhalation: No data available
LD50 Dermal - Rat - male and female - > 2,000 mg/kg (OECD Test Guideline 402)
Remarks: (71% solution) (ECHA)
LD50 Intraperitoneal - Mouse - 100 mg/kg
Skin corrosion/irritation
Skin - Rabbit
Result: slight irritation - 4 h (OECD Test Guideline 404)
Remarks: (71% solution) (ECHA)
Serious eye damage/eye irritation
Eyes - Rabbit
Result: slight irritation - 72 h (OECD Test Guideline 405)
Remarks: (71% solution) (ECHA)
Respiratory or skin sensitization
Local lymph node assay (LLNA) - Mouse
May cause sensitisation by skin contact.
(OECD Test Guideline 429)
Remarks: (ECHA)
Germ cell mutagenicity
Test Type: in vitro assay
Test system: S. typhimurium
Result: negative
Carcinogenicity
Classified based on available data. For more details, see section 2
Reproductive toxicity
Classified based on available data. For more details, see section 2
Specific target organ toxicity - single exposure
Classified based on available data. For more details, see section 2
Specific target organ toxicity - repeated exposure
Classified based on available data. For more details, see section 2
Aspiration hazard
Classified based on available data. For more details, see section 2

SECTION 12: Ecological information

Ecotoxicity

Components:

Ammonium thioglycolate:

Toxicity to fish
Remarks: No data available

Persistence and degradability

Components:

Ammonium thioglycolate:

Biodegradability
Remarks: No data available

Bioaccumulative potential

Components:

Ammonium thioglycolate:

Bioaccumulation
Remarks: No data available
Partition coefficient: noctanol/water
log Pow: 2.85

Mobility in soil

Components:

Ammonium thioglycolate:

Stability in soil
Remarks: No data available

Other adverse effects

Components:

Ammonium thioglycolate:

Additional ecological information
No data available

SECTION 13: Disposal considerations

Disposal methods

Waste from residues
Offer surplus and non-recyclable solutions to a licensed disposal company.

SECTION 14: Transport information

International Regulations

IATA-DGR

UN/ID No. : UN 2922
Proper shipping name : Corrosive liquid, toxic, n.o.s.
(Ammonium thioglycolate)
Class : 8
Subsidiary risk : 6.1
Packing group : III
Labels : Class 8 - Corrosive substances, Division 6.1 - Toxic substances
Packing instruction (cargo aircraft) : 856
Packing instruction (passenger aircraft) : 852

IMDG-Code

UN number : UN 2922
Proper shipping name : CORROSIVE LIQUID, TOXIC, N.O.S.
(Ammonium thioglycolate)
Class : 8
Subsidiary risk : 6.1
Packing group : III
Labels : 8 (6.1)
EmS Code : F-A, S-B
Marine pollutant : no

Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code

Not applicable for product as supplied.

National Regulations

JT/T 617

UN number : UN 2922
Proper shipping name : CORROSIVE LIQUID, TOXIC, N.O.S.
(Ammonium thioglycolate)
Class : 8
Subsidiary risk : 6.1
Packing group : III
Labels : 8 (6.1)
Environmentally hazardous : no

Special precautions for user

The transport classification(s) provided herein are for informational purposes only, and solely based upon the properties of the unpackaged material as it is described within this Safety Data Sheet. Transportation classifications may vary by mode of transportation, package sizes, and variations in regional or country regulations.

SECTION 15: Regulatory information

Catalogue of Hazardous Chemicals : This product is not listed in the catalogue of hazardous chemicals, but it meets the definition of hazardous chemicals and its principles of determination.

National regulatory information

Law on the Prevention and Control of Occupational Diseases

Regulations on Safety Management of Hazardous Chemicals

Identification of Major Hazard Installations for Hazardous Chemicals (GB 18218)

Not listed

Hazardous Chemicals for Priority Management

Not listed under SAWS

Catalogue of Specially Controlled Hazardous

Not listed Chemicals

List of Explosive Precursors

Not listed

Regulations on Labour Protection in Workplaces where Toxic Substances are Used

Catalogue of Highly Toxic Chemicals

Not listed

Regulation of Environmental Management on the First Import of Chemicals and the Import and Export of Toxic Chemicals

China Severely Restricted Toxic Chemicals for Import and Export

Not listed

Regulation on the Administration of Precursor Chemicals

Catalogue and Classification of Precursor Chemicals

Not listed

Regulations on the Administration of Controlled Chemicals

List of Controlled Chemicals

Not listed

Regulations of Ozone Depleting Substances Management

List of Controlled Ozone Depleting Substances

Not listed

List of Controlled Ozone Depleting Substances Import and Export

Not listed

Environmental Protection Law

List of Priority Controlled Chemicals

Not listed

List of Key Controlled New Pollutants

Not listed

SECTION 16: Other information

Full text of other abbreviations

ACGIH
USA. ACGIH Threshold Limit Values (TLV)
ACGIH / TWA AIIC - Australian Invent Transport by Land of Bra bw - Body weight; CMR Standard of the German List (Canada); ECx - Conc associated with x% respo Chemical Substances (Jap response; ERG - Emerge GLP - Good Laboratory P cer; IATA - International Construction and Equipm Half maximal inhibitory c tion; IECSC - Inventory o tional Maritime Dangerou Industrial Safety and H Standardization; KECI - K tration to 50 % of a test (Median Lethal Dose); MA lution from Ships; n.o.s. No Observed (Adverse) E fect Level; NOELR - No Norm; NTP - National Toxi icals; OECD - Organizatio fice of Chemical Safety a and Toxic substance; PIC stances; (Q)SAR - (Quant (EC) No 1907/2006 of th Registration, Evaluation, Accelerating Decompositi Chemical Substance Inve Thailand Existing Chemica States); UN - United Nat Transport of Dangerous WHMIS - Workplace Hazar
8-hour, time-weighted average ry of Industrial Chemicals
ANTT - National Agency for il
ASTM - American Society for the Testing of Materials
- Carcinogen, Mutagen or Reproductive Toxicant
DIN nstitute for Standardisation
DSL - Domestic Substances ntration associated with x% response
ELx - Loading rate se
EmS - Emergency Schedule
ENCS - Existing and New n)
ErCx - Concentration associated with x% growth rate cy Response Guide
GHS - Globally Harmonized System
actice
IARC - International Agency for Research on Canir Transport Association
IBC - International Code for the nt of Ships carrying Dangerous Chemicals in Bulk
IC50 ncentration
ICAO - International Civil Aviation Organiza- Existing Chemical Substances in China
IMDG - Interna- Goods
IMO - International Maritime Organization
ISHL alth Law (Japan)
ISO - International Organisation for rea Existing Chemicals Inventory
LC50 - Lethal Concenopulation
LD50 - Lethal Dose to 50% of a test population POL - International Convention for the Prevention of Pol- Not Otherwise Specified
Nch - Chilean Norm
NO(A)EC fect Concentration
NO(A)EL - No Observed (Adverse) Efbservable Effect Loading Rate
NOM - Official Mexican ology Program
NZIoC - New Zealand Inventory of Chemfor Economic Co-operation and Development
OPPTS - Ofd Pollution Prevention
PBT - Persistent, Bioaccumulative S - Philippines Inventory of Chemicals and Chemical Subtative) Structure Activity Relationship
REACH - Regulation European Parliament and of the Council concerning the uthorisation and Restriction of Chemicals
SADT - Selfn Temperature
SDS - Safety Data Sheet
TCSI - Taiwan tory
TDG - Transportation of Dangerous Goods
TECI s Inventory
TSCA - Toxic Substances Control Act (United ons
UNRTDG - United Nations Recommendations on the oods
vPvB - Very Persistent and Very Bioaccumulative
ous Materials Information System
Disclaimer:

The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.

Recommended Products
AMMONIUM SDS 2-Ethylhexyl mercaptoacetate SDS 2-Thiobarbituric acid SDS Thioglycolic acid SDS Ammonium chloride SDS POTASSIUM THIOGLYCOLATE SDS Ethanethiol SDS Ammonium thiosulfate SDS Glycolic acid SDS Ammonium sulfate SDS